Stealth Racing VR6 Turbo Kits

[Vince@Stealth]

OK this one is our Corrado Turbo 9psi vs Golf MK2 VR6 Turbo OBD1 (Hot Film MAF), 15Psi Boost, Short Runner Intake.
The MK2 has the pretty much the same turbo as ours except a 0.82 Exhaust Housing....(ours is 0.68 Hot)
I only Tuned this car for the owner as fitted all the turbo kit himself .

Funnily enough we are fitting a turbo kit this week in a MK3 VR6 OBD2 with the same Turbo that is in that MK2.
I'll Let you know how it turns out.

[Vince@Stealth]

Is there any chance of seeing it up against a similar rotrexed VR? This was going to be the route I was going for. Now after seeing this it may of changed my mind towards going turbo!

Stealth Turbo 9psi Blue
Rotrex 18psi Green

Corrado with Rotrex has SP263 Cams and Short Runner......We fiited all this for our customer then remapped it.


Worth mentioning here that the Rev limiter on our Corrado is stock, ie not upped

[Vince@Stealth]

Stealth Corrado Turbo (Blue)
vs
Jons Corrrado Turbo (Purple).... This car is OBD2, short runner, customers own DIY Install and Stealth Remap.
In my opinion this turbo is slightly too small just about peaks at 15psi but can't sustain it.
Spools very fast and possibly into gearbox breaking territory??
I had some fun with a camcorder while remapping this one http://www.youtube.com/watch?v=qzViW2sidNE

[Vince@Stealth]

OK Last set of power Dyno Plots

This is how NOT to turbo a VR6, the turbo is so small that it almost becomes a restriction in the exhaust system once the rpm's start to climb

[Vince@Stealth]

I hope this gives you all a little bit of insight into why we followed the route that we did?

Any questions or Comments please fire away?

[Vince@Stealth]

Wow, those plots are a lot closer than I thought they would be. Very impressed at how smooth the torque curve is on your VRT vince, do you think that's down to the use of the standard manifold?

Thank You for your positive comment.

There are possibly many factors here and yes the stock manifold could be one of them.

Vince

[Wendy]

Driven it. !!!

Impressive stuff, and had a big grin on my face all day after.!!!!!

Well, Vince had to make sure it passed the Wendy Test, before letting you guys loose with it !!!

[kevhaywire]

Guys

Sorry, but I've had to clean this thread up because it's in the Suppliers section and Vince needs to keep it clear for information relating to the kit and for any announcements etc.

The old thread has been copied over to the Engine bay for general discussion and no one's posts have been removed.

Please keep any chat / banter in here please - viewtopic.php?f=1&t=89101

Questions and comments for Vince relating to specifically to his kit can remain in here!

Thanks

[perksy]

hi vince looks very inpressive stuff, i was just wondering if you have a supply and remap price for the kit for thoes who want to put it in on there own?

[Vince@Stealth]

hi vince looks very inpressive stuff, i was just wondering if you have a supply and remap price for the kit for thoes who want to put it in on there own?

Hi Perksy

At the moment all the kits will be fitted in our workshop, 2 reasons for this.

Firstly it's early days, we just want to ensure all installs fit perfectly, if there are any problems then we can overcome /correct them in our workshop. This may not be so easy for a DIY fitter?
Secondly, hopefully you will have noticed that our fitted price is very good? Trust me when I tell you that if we were to count up all the hours it takes to fit the kit + the cost of the bits it would come to quite a bit more than £4400. So the deal is good.
Therefore that leaves me with a bit of a dilemma, yes sure the DIY kit will be cheaper but at the moment costing the kit this way is my problem.

As things progress this may change but at the moment I can't give you any dates or prices.

I hope you understand?

Vince

[perksy]

Hi Perksy

At the moment all the kits will be fitted in our workshop, 2 reasons for this.

Firstly it's early days, we just want to ensure all installs fit perfectly, if there are any problems then we can overcome /correct them in our workshop. This may not be so easy for a DIY fitter?
Secondly, hopefully you will have noticed that our fitted price is very good? Trust me when I tell you that if we were to count up all the hours it takes to fit the kit + the cost of the bits it would come to quite a bit more than £4400. So the deal is good.
Therefore that leaves me with a bit of a dilemma, yes sure the DIY kit will be cheaper but at the moment costing the kit this way is my problem.

As things progress this may change but at the moment I can't give you any dates or prices.

I hope you understand?

Vince

a up vince i more than understand, its not a problem i do think the price is amazing to say that its fitted
tbh im not in any real rush, i was more thinking for the future at the min im in 2 minds in which way to go turbo , supercharged so at the min im just bein noesy and tryin to get an idea of the cost, but i deffo wana fit it myself when i do come to go forced induction
well i just wana say with them figures thats an amazing stage 1 kit, i look forward to future progress
and also i may need your services in the near future for a little remap on my N/A vr

[Vince@Stealth]

[/quote]

at the min im in 2 minds in which way to go turbo , supercharged
[/quote]

I think a test drive of each may make your mind up for you

[perksy]

I think a test drive of each may make your mind up for you

is that an offer , if so when i come down for a remap ull have to take us out

[Vince@Stealth]

[/quote]


is that an offer , if so when i come down for a remap ull have to take us out[/quote]

Yes for sure, that is why we bought our own C, it's what's it's there for.

Also a very sneaky way of me getting my own Corrado VR6T

[lilfuzzer]

Hi Vince mate mate was wondering if it was you that rebuilt his gearbox? The car in question was a 20vt syncro with a rallye box apparently the guy that done the car was called cam not sure of spelling

cheers

also I was wondering about re-maps for a turbo rado what do I need to do to book it in etc will it take a while or do I have time to come down and back in one day I am in sunderland north east of england. cheers