Tab Content
  • fla's Avatar
    20 Hours Ago
    fla replied to a thread Starter motor speed in Engine Bay
    Checked it earlier it was 12.3volts. But put it on charge anyway so I'll see again in a few hours
    6 replies | 142 view(s)
  • fla's Avatar
    1 Day Ago
    fla replied to a thread Slow to start when warm in Engine Bay
    Dox I'll swop out the cam sensor and see how it goes - obd1 and 2 have the same one Rob - put in a check valve in the fuel line by the fuel pump....
    58 replies | 6567 view(s)
  • fla's Avatar
    1 Day Ago
    fla replied to a thread Starter motor speed in Engine Bay
    Voltage is around 11.8 battery is new. Got an exchange unit from gsf. Bosch.
    6 replies | 142 view(s)
  • fla's Avatar
    1 Day Ago
    fla started a thread Starter motor speed in Engine Bay
    I fitted a new starter last year aeound november. Itvused to turn the engine over very quickly indeed but now seems to jave slowed down a bit. Is...
    6 replies | 142 view(s)
  • fla's Avatar
    1 Day Ago
    fla replied to a thread Slow to start when warm in Engine Bay
    Cranking is normal speed just takes about 10 or 11 turns before it fires. Ive got a new crank sensor so will try that. I also thought that the fuel...
    58 replies | 6567 view(s)
  • fla's Avatar
    1 Day Ago
    fla replied to a thread Slow to start when warm in Engine Bay
    Trying to put some logic here: If the car cranks but doesnt fire there is a combination of no spark or fuel in the engine. If we assume that the...
    58 replies | 6567 view(s)
  • fla's Avatar
    2 Days Ago
    This ^^^^ looks like a dream office! Need anyone to run the commercial side of the business???
    26 replies | 654 view(s)
  • fla's Avatar
    3 Days Ago
    fla replied to a thread My oettinger in Members Gallery
    very nice. Interesting that the door cards dont have the sections that the regular leather interiors have
    45 replies | 3916 view(s)
  • fla's Avatar
    3 Days Ago
    fla replied to a thread Screen wash tubes in Wanted
    you can take it apart - i posted a stripdown of my spray jet: http://the-corrado.net/showthread.php?74917-heated-washer-jet-wire-repair-with-pics
    9 replies | 147 view(s)
  • fla's Avatar
    3 Days Ago
    fla replied to a thread Slow to start when warm in Engine Bay
    i fitted a check valve to my fuel pump but this didnt make any difference. Ive also used a new emulator and after a scan there were no error codes...
    58 replies | 6567 view(s)
  • fla's Avatar
    3 Days Ago
    fla replied to a thread Screen wash tubes in Wanted
    slice a slot in it along the length and peel back. If necessary, spray some wd40 to attack the glue. Should enable you to remove it.
    9 replies | 147 view(s)
  • fla's Avatar
    1 Week Ago
    good suggestion BB - just ordered some from Ebay. I'll give them a go and see how they turn out. presumably they can then be cleaned and...
    4 replies | 206 view(s)
No More Results

2 Visitor Messages

  1. View Conversation
    Hi mate would be interested in your lowering cups! 07859238100
Showing Visitor Messages 1 to 2 of 2
About fla

Basic Information

About fla
Location:
Middx
Interests:
Corrados (of course!) Electronic music (Depeche Mode, Frontline assembly etc)

Signature


Hasan
VR6 Auto to manual conversion, beige leather, aircon, TT comps, blue dash lights & switches, Koni TA/Nothelle springs, OBD2, 264 cams

my car

Statistics


Total Posts
Total Posts
5,955
Posts Per Day
1.27
Visitor Messages
Total Messages
2
Most Recent Message
10th November 2016
General Information
Last Activity
33 Minutes Ago
Join Date
10th September 2004
Referrals
0

1 Friend

  1. zak zak is offline

    Enthusiast

    zak
Showing Friends 1 to 1 of 1
About us
We are the world's largest community for VW's Super Coupé! Be it 8v, 16v, G60 or VR6 (or maybe something else!), everybody's welcome! If this is your first visit, be sure to click register and fill out your details before you can post.
Help us
This site is run on donations.
Please help keep the forum alive!
Follow us
advertising & sponsorship
Are you a company looking for advertising that could benefits our users? For site & forum sponsorship, please see our dedicated microsite here.