Results 1 to 2 of 2

Thread: Road / Track Day car - 1.8T

  1. #1
    Newbie
    Join Date
    19th October 2018
    Location
    Somerset
    Posts
    9

    Road / Track Day car - 1.8T

    Hi, new here and a while back I got a 16v rolling shell from Monkey and Paulina locally. Itís ropey, but is getting a decent going over, mechanically at least.
    Pinched this photo of it while Paulina was driving it at the Mk2OC Curborough day



    They had it converted it to VR6 but moved on to a tidier Storm model and started fresh.
    It had sat outside untouched due to other cars until a few weeks ago but trying to make up for lost time now!

    So we got it inside and up on stands strip it down



    EXCUSE IT BEING SERIOUSLY DIRTY! As itís a dual purpose road and track car, I wanted a cage of some sort for mounting harnesses and keeping the roof up if it goes over.
    The flip side was I didnít want the usual risk of caving your head in while driving on the road without a helmet.

    We got a main hoop and some extra 44.5mm CDS tube from Cyclone Racing and then lent it back slightly, trying not to go too far.
    Then we cut the rear stays, diagonal and strut brace to suit. The hoop still follows the pillar enough to be able to add to it and meet MSA regulations.
    That's if the car ever evolves / changes to a pure track car or race car later, for now itís enough to tick the boxes it had to and looks alright so all good





    Then put the seat tubes in and gave it all a ghetto coat of satin battleship grey from an agricultural / industrial supply place.
    It's smooth enough, hard wearing and there wonít be any glare off it, so should be alright although it isn't anything fancy.



    After that we started unbolting things. The rear beam was in a bit of a state and the bushes were pretty much hanging out



    Binned the gammy old brake lines, pipes and bushes and then took an abrasive wheel in the angle grinder to any rusty bits.
    Got the rusty patches back to clean good metal and thinned out the rest of the coating on the good bits across the rest of it, then wire wheeled the awkward to get at bits around studs and brackets and whatnot

    Checked it over and it looked alright and cleaned up okay so gave it a coat of red oxide



    Then a coat of black stone chip and sating black paint

    Also did the same with the front wishbones as they were in a similar state and then started getting the new bushes in.
    Should tidy things up a bit and I can get some more life out of them



    Next job chassis wise is going to be changing the tie rods, gaiters and rod ends as well as the lower ball joints.
    Theyíre pretty disgusting and I can totally see them causing grief if things need to come apart for maintenance or alignment changes later.
    I also got new discs and pads front and rear, braided lines, front caliper seal kits, Mk4 rear calipers and new wheel bearings, so should be an improvement.

    Before that weíll be having a bash at the engine so hopefully that goes smoothly.

    Anyway, up to date now so more updates soon, thanks

  2. #2
    Newbie
    Join Date
    19th October 2018
    Location
    Somerset
    Posts
    9
    Another big bit of the puzzle ready, the engine is now good to go, minus some hoses and fluids.

    Basically started with a dopey old AGU engine and ME3.8 ECU, swapped to a K03S turbo, added a Forge actuator, Forge recirc valve, Forge baffled sump, Creations Motorsport turbo intake pipe,
    Saab red injectors, new heat exchanger, cambelt kit and tensioner, alternator, colder plugs gapped for some proper boost, and probably a few more bits Iíve forgotten like gaskets and bolts and stuff.
    Cleaned out the oil pickup as well, because 1.8T



    Took a fair bit of time to clean it up, get the painting and powder coating done and all that stuff.
    It looks a lot better than it did when we pulled it out of a dirty Mk4 though so hopefully itíll look good in the bay





    Also put on a lightened G60 flywheel and a new Sachs VR6 clutch, and on the subject of transmission stuffÖ
    I also had a painfully long-awaited parcel turn up, which was nice



    And as the drivers side driveshaft looked okay, but the passengers side one very much wasnít, got a new one from J&RÖ
    GKN bearings, decent steel, good rubber boots and a 2 year warranty, canít lose!



    The diff has been fitted now, with the usual ARP bolts / fresh diff bearings combo, so onto the engine and into the car tomorrow

    Fingers crossed tomorrow is productive and Iíll have another update, thanks

Similar Threads

  1. My ice grey vr6 track/fast road build
    By kennyvr671 in forum Archive
    Replies: 24
    Last Post: 13th May 2018, 9:42 PM
  2. Replies: 11
    Last Post: 22nd July 2014, 8:23 PM
  3. Fast Road and Track day Parts / Fitting / Set-Up
    By Corby Motorsport in forum Suppliers Forum
    Replies: 0
    Last Post: 12th March 2010, 9:00 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
We are the world's largest community for VW's Super Coupť! Be it 8v, 16v, G60 or VR6 (or maybe something else!), everybody's welcome! If this is your first visit, be sure to click register and fill out your details before you can post.
Help us
This site is run on donations.
Please help keep the forum alive!
Follow us
advertising & sponsorship
Are you a company looking for advertising that could benefits our users? For site & forum sponsorship, please see our dedicated microsite here.