andy.b

Is there a post on this forum that cover this topic? or can anyone help?

do you know where the cheapest place is to get these CAM'S?

ANYONE THERE?

i am looking to do a top end re-build on my 2.9 VR6 CR6 Corrado. i need to know what is the best CAM i can get for the right price and from which supplier. is this subject covered else where? Please Help

i have just been quoted by Awesome GTI £1300 + VAT for the following engine work: .Timing chains .Full top end re-build is this worth it?

I HAD THESE REPLACED AND CHECKED OUT

Could this problem be my Gearbox Diff on its way out on my VR6 Corrado. Last month I was driving my car and I noticed a slight wobble, I though this was the road surface. As the weeks have gone by the wobble and knocking noise has got worse, to the point where you can feel the knocking/wobbling in the car. The car is at the garage at the moment and they have checked my wheel bearings and all other things front and back of car and everything is fine, they said my diff in the gearbox is very noisy. Could this be my above problem?

Where can I get a re-conditioned gearbox from for my 2.9 Corrado VR6? And how much am I looking at

If the Relay and Fuse Board for my radiator fan on my C VR6 was Kaputt would it cause my fan not to work properly. i.e, your radiator fan comes on a 90-92 dgress “speed 1”, 100-103 degrees “speed 2” and 120 degrees “speed 3”. My radiator fan only comes on at 100-103 degrees “speed 2” and it only blows really slowly and my car seems to running round in the high 90’s low 100’s. When I first got the car and up until 2 months ago my radiator fan used to come on at 90-92 degrees. If the relay and fuse board was Kaputt would it cause this to happen.

what do you meen by check the 'screw down' fuse? is that the one above the gearbox in the engine bay? i have replaced Speeds 1 and 2 - two way rad fan switch, bottom of the radiator. the switch in the bottom of the radiator! it screw in doesnt it? and it has three pins on it yep? if so i have replaced that one! thanks for your help

Stage 1 on my cooling fan is not working, i have been told stage 1 of the fan is at 90-92 degrees "water temp". this was working properly 2 months ago and now my engine is over-heating. i have replaced with genuine new VW parts: Radiator Fan Water housing Thermostat Coolant Two stage fan sensor "bottom of rad" stage 2 works fine 100-103 degrees it comes on. are there any fuse relays that make this work?

Does anyone know where i can get some fancy number plates from to finish of my corrado VR6 project

and is that the water temp you on about mate that goes to 150

2.9 VR6

Hello people, my car engine 2.9VR6 has started to over heat for the past 2weeks now. when i am cruising around town the water temp gauge stays at 90 degrees, but when i thrash my car about it goes towards 100 degrees and does not go back down. when i first got the car 11 months ago up untill 2 weeks ago it ran bang on 90 degrees even when i thrashed it. i have had a genuine new radiator, fan, fan sensor and i have also had my water pumps checked out by VW. when i first got the car i replaced my thermostat "could my thermostat be the problem? please help

My car (VR6 Corrado) is in the body shop at the moment and they have just tolled me they are strugling to remove my original bumper. where are the fixing points for my front bumper? also i have bought a full reiger RS front bumper (part of the reiger GTX body kit) and i want to no the best way to fix this to my car? cheers!

What are these mate? are they callipers and discs and pads you buy in a package? how much and where from? the mechanic at VW said he cleaned the Calliper carrier but i dont no if he cleanded the sliding pin

yes mate that wheel where the brake pad is squeeking is hotter than the other

sound, cheers lads. i was getting abit paranoid about my car thats all. just re-tested it and yep water 90-92 on a run and oil 102-104 at 80mph, standing still water 96-98 and oil 96-98

ha ha, i do feel like doing that sometimes when my VR is pissing me of.

is my engine okay then if the water temp is 90-92 on a run and 96-98 in traffic?

How do i tell if this have worn to access? what will i experiance in my car if they have gone?

i was sat in my car so i dont no, tomoz morning a will start it an check if it smells of burnt oil

Sorry i have been mistaken, the needle next to my speedo "water temp" shows 90-92 when on a run and 96-98 in traffic, is this okay? my oil is around 100 i think, ill check this out. i got told that the MFA is inacurate, is this true? how much is the mocal oil cooler? and where can i get one from?

I have had this problem with my corrado VR6 for ages, only my front passenger side brake pad is squeaking realy loud and its pissing me off. I have taken my car to the garage 4 times now for them to clean my caliper and put some of that copper greese on my pad to stop it squeaeking but it keeps coming back. What can I do to stop this? The garage have checked my driver's side caliper, pads and disk and they're the same as the passenger side, funny how it's only the passenger side.