ger040 2 Posted November 8, 2020 does anyone know the part number for the following oil pressure sensor it is located on the braided charger line at cylinder head cannot find it on etka and vw dealer cannot find it either - its brown in colour my own has decided to ooze oil Quote Share this post Link to post Share on other sites
vw rule 19 Posted November 9, 2020 Hello there, I think it's number (1)** in the attached Etka photo image, also you could use the first number (2)** that's listed, BUT YOU'LL HAVE TO DOUBLE CHECK THE PRESSURE RATING BEFORE PURCHASING, as they can sometimes range from 0.25, 0.3 and 0.4 Bar. Yours I think is the 0.3 Bar one BROWN, but you can get them in colours white or red, but like I say you'll have to double check the pressure before purchasing one. Also I've listed below all the oil pressure and temperature sensors, that are used on the 4 cyl Corrado engine's on the cylinder head and engine block areas. (1) ** Low oil pressure switch set at 0.25 or can be 0.4 Bar (blue) or set at 0.3 Bar (brown) Single spade contact. Thread 10mm X 1mm Part number 028 919 081H (2) ** Low oil pressure switch set at 0.3 Bar (white) or can be (red) sometimes. Single spade contact. Thread 10mm X 1mm Part number 056 919 081 (2) High oil pressure switch set at 1.6 to 2.0 Bar (white) Single spade contact. Thread 10mm X 1mm Part number 056 919 081C (2) Oil pressure switch set at 1.2 to 1.6 Bar (black) Single spade contact. Thread 10mm X 1mm Part number 068 919 081D (2) Oil pressure switch set at 0.75 to 1.0 Bar (grey) Single spade contact. Thread 10mm X 1mm Part number 068 919 081C (8) Coolant temperature sender (mainly for KR and 9A engines) Part number 049 919 501 All the above oil pressure switches and the coolant temp use the same sealing washer (9) Part number N0138115 (21) Oil pressure switch for oil gauge (large cylindrical type) Set at 1.8 bar (black) Double spade/nut contacts. Thread 10mm X 1mm Part number 035 919 561A Normally fitted to oil filter housing. (21) Oil pressure switch for oil gauge (large cylindrical type) range from 0 bar up to 10 bar. Single spade contact. Thread 10mm X 1mm Part number 535 919 561B Normally fitted to oil filter housing. (22) Oil temperature sensor Part number 049 919 563A (22) Oil temperature sensor Part number 1H0 919 563 Hope this helps Si Quote Share this post Link to post Share on other sites
ger040 2 Posted November 10, 2020 On 11/9/2020 at 6:33 PM, vw rule said: Hello there, I think it's number (1)** in the attached Etka photo image, also you could use the first number (2)** that's listed, BUT YOU'LL HAVE TO DOUBLE CHECK THE PRESSURE RATING BEFORE PURCHASING, as they can sometimes range from 0.25, 0.3 and 0.4 Bar. Yours I think is the 0.3 Bar one BROWN, but you can get them in colours white or red, but like I say you'll have to double check the pressure before purchasing one. Also I've listed below all the oil pressure and temperature sensors, that are used on the 4 cyl Corrado engine's on the cylinder head and engine block areas. (1) ** Low oil pressure switch set at 0.25 or can be 0.4 Bar (blue) or set at 0.3 Bar (brown) Single spade contact. Thread 10mm X 1mm Part number 028 919 081H (2) ** Low oil pressure switch set at 0.3 Bar (white) or can be (red) sometimes. Single spade contact. Thread 10mm X 1mm Part number 056 919 081 (2) High oil pressure switch set at 1.6 to 2.0 Bar (white) Single spade contact. Thread 10mm X 1mm Part number 056 919 081C (2) Oil pressure switch set at 1.2 to 1.6 Bar (black) Single spade contact. Thread 10mm X 1mm Part number 068 919 081D (2) Oil pressure switch set at 0.75 to 1.0 Bar (grey) Single spade contact. Thread 10mm X 1mm Part number 068 919 081C (8) Coolant temperature sender (mainly for KR and 9A engines) Part number 049 919 501 All the above oil pressure switches and the coolant temp use the same sealing washer (9) Part number N0138115 (21) Oil pressure switch for oil gauge (large cylindrical type) Set at 1.8 bar (black) Double spade/nut contacts. Thread 10mm X 1mm Part number 035 919 561A Normally fitted to oil filter housing. (21) Oil pressure switch for oil gauge (large cylindrical type) range from 0 bar up to 10 bar. Single spade contact. Thread 10mm X 1mm Part number 535 919 561B Normally fitted to oil filter housing. (22) Oil temperature sensor Part number 049 919 563A (22) Oil temperature sensor Part number 1H0 919 563 Hope this helps Si Thanks Si, That's a great help Quote Share this post Link to post Share on other sites
vw rule 19 Posted November 10, 2020 4 hours ago, ger040 said: Thanks Si, That's a great help No worries. According to the Bentley manual the torque setting for the oil pressure switches is 25 Nm (18 ft Ib) Photo image from the Bentley manual attached below. Si Quote Share this post Link to post Share on other sites
ger040 2 Posted November 11, 2020 thanks again Quote Share this post Link to post Share on other sites
