dinger657

just a 1.8, no turbo.......yet

hi all what do you think of my new motor? sadly last year the rado had to go as 2 x baby seats + angry wife = no more 'rado :( (i even had to buy a mondeo at first :oops:) but now i have this!

mine sounds awesome and looks the dogs! was hitting every speed bump :oops: but raised the front end about 1.5 inches now no scrapes! :wink:

MMMMMMMMMM NICE!

ive done 147k lol!

white g60 in colchester! let you out of the garage! very low and big rims looked good, h reg, anyone on here? :)

thats where i went for my clutch, asked them but they only do mechanical stuff, wouldnt touch the sunroof!

hi i have a replacement sunroof mech to replace my knackered one, does any one know of anyone in the colchester area who can fit it for me, i have tried once before, it took me hours and i ended up putting knackered one back in! cheers matt

got a new bumper just need to spray it and purchase front splitter!

just up loaded these what do u think? :salute:

got some fk coilovers, need to lower the back, i have the two hook shaped spannners, was just wandering how i do this, do i just take the wheels off and wind then down or is it a bit more complicated? cheers matt ps im a car mong not very good with tools!

I was at CORSHAM 2day, where i saw a VR6 and a 16V parked next 2 each other by the crab firestation, i know you are on here as your forum stickers were on display! :salute:

cleaned all fuses, dim dip resistor not connected as im using an uprated loom, all been working fine for about a year and now nothing only thing to try is the switch!

tried that as well still no joy! looks like daytime driving for me!

how will i know if the switch is gone apart from getting another?

help! my headlights have decided to give up working, i have side lights and full beam but no dipped beam! they were working fine earlier, all of a sudden nothing, i have checked the fuses and they are fine, anyone any ideas? cheers matt

cant beat best of guns'n'roses to drive to!

my wheels are 17'' enzo cups :wink:

same wheels as mine, look good when not curbed! :(

cheers for the replies, think i will get it back on ebay asap!

HI JUST GOT A TT FUEL CAP ON EBAY, WAS JUST WONDERING IF ANY1 HAS FITTED ONE YET? SHALL I BOTHER OR JUST SELL IT ON? CHEERS

heres the instructions in with the loom 1. 1st disconnect the dipped beam feature plug, this is situated in front of the battery and is usually a white or yellow plug with 2 wires coming out of the terminal that are about 10 cm long and attached to the chasis. one wire is yellow/black and the other is plain yellow. just disconnect the plug and secure it, as this function is overruled by the new loom. 2. the next thing to do is to connect the neg earth wire with ring terminal on the new loom marked n-, this can be connected direct to the neg post on the battery or to the earth point behind the battery, which is bolted with a 10mm nut. 3. then take the 20 amp fuse out of the holder on the new loom and connect the ring terminal marked p+ directly on to the battery, as this is going to be the new main feed for the headlamps. 4. on the drivers side you will need to locate the yellow wire that carries the 12v feed to the headlight, this runs along side the engine with other wires to the back of the headlight plug and is covered in a material covering. you need to cut this wire and attach wire marked o/s from the new loom onto the yellow wire coming from the headlight plug. make sure the bare wire is pushed right inside the butt connector, and squeeze firmly together with pliers. the other yellow wire thats left will need to be taped up securely and discarded, as this is no longer needed. 5. now you need to cut the yellow and black wire on the nearside loom which carries the 12v to the headlight, as b4 you need to connect the yellow butt connector marked n/s to the yellow and black wire coming from the headlight plug and connect the remaining yellow/black wire coming from the cars loom to the butt connector marked L on the loom. again ensure there is a good connection b4 you close the butt connections. 6. finally tidy up the wires with the cable ties provided and reinsert the 20amp fuse. now test your lights.

his ebay id is jaymab, from somewhere in nottingham

just fitted this and followed instructions exactly, however my headlight switch now does not work properly, in the middle position when youd expect sidelights i now get dipped beam and in the left position where you normally get dipped beam i now get side lights on! when the switch is in the middle position full beam will not stay on so i need to sort this out, anyone any ideas?

where can i get my hands on some lupo wiper arms? cheers