Jump to content

DanRVW

Members
  • Content Count

    14
  • Joined

Everything posted by DanRVW

  1. DanRVW

    Rear Lights

    Im in Hull unfortunately
  2. O/S early wing? Doesnt matter about colour or condition as long as there are no rust holes or big dents :)
  3. No problem :) Kinda get used to having my car off the road owning a corrado haha.
  4. DanRVW

    Rear Lights

    Ive got a pair of inners. Excellent condition. £20 posted.
  5. I dont suppose any of you can post it? Im in Hull and my car is off the road for a few weeks :(
  6. Just need an early spec drivers side wing if anyone has one. Any colour or condition providing there are no massive dents or rust holes... Thanks :)
  7. Hey everyone. I need a few bits to finally get my corrado project finished. I need: Centre console (around hand brake lever) Drivers side door seal (the inner seal on the car itself) Passenger side footwell vent The housing for the interior light and sunroof switch on the headlining The small covers for the screws on the insert that goes on the clocks All for an early model. If anyone has any of these, let me know! :) Thanks :)
  8. Thanks for the help :) I wanted to use a MK4 pump to make things simple (i got the pump and lines from a local scrappy for £10) and ditch the rusty old hanger and pump under the car....i thought it was as easy as just getting a different fuel tank, hance buying a Mk3 VR6 one, which was close but filler neck sticks too far out :/...and then playing with the idea of chopping it and plastic welding it etc..which i wasnt too fond of. And now i know the corrado ones are different sizes etc and there probably isnt a bolt on solution to this, i might aswell go with the original set-up and keep the 2 pumps... Thank you anyways :)
  9. Has it got the large fuel pump hole or the small one?
  10. Thanks. Im hoping to put a S3 fuel pump in, and modify it to get the fuel gauge to read somewhere near where it should. I may have to just try a VR6 tank and hope i can make it fit...
  11. If possible...Id like know the differences between all of the fuel tanks on corrado's if anyone can enligten me, ive tried to search the net and these forums but cant find a lot of info on them. Ive got an early 1990 16v with the small lift fuel pump like Mk2 Golf GTi's but want the larger fuel pumps as found in VR6's and later C's. I got myself a MK3 Golf VR6 fuel tank as i heard they were the same, but the filler neck sticks out about 10mm too far so the flap wont close(though the rest of the tank fits ok) so im thinking a later corrado tank will fit, but have heard they are different sizes 55ltrs/70ltrs? and the boot floor is different? But...Will a VR6 tank fit on my car? If not will a later G60/2.0L tank be a better fit? Or is it just a case of diffent tank straps? Help would be appreciated a lot! :)
  12. Cheers dave! Didnt know you were on here tbh. Ill see about getting a servo (whats the 9" one off?)....mines rusty as hell so i need a new one. Is the G60 Master cylinder for ABS? Im guessing the VR6 one is. Yea...i did consider converting to 5 stud...but ive bought most of the stuff to build my front subframe and suspension up..and id need another rear axle so im keeping it 4 stud. Ill put all the photos on of the build once its done ;) And yea...the old engine is going back in the A3 in the next few weeks :) Hows yours going?
  13. Hello everyone! Im kinda new to this forum...but ive got some questions which have been giving me some headaches lately. :brickwall: Before anyone says its been covered, I have searched and searched the internet for more info as well as these forums but ended up more confused haha :cuckoo: (and there isnt much info as to exactly which pads are required) Ive bought some Twin pot Audi calipers (G60 Girling ones). Ive got the 280mm G60 discs. But as they are Audi S2 calipers, i ordered pads for an S2 coupe with the G60 discs from Venom. These ones: http://www.venommotorsport.com/product_details.php?id=12200&manufacturer=Black%20Diamond&category=Brake But when they turned up, they are for single piston calipers and are the wrong size. After looking further on venom and looking at the brake pad shape and dimension guide on there, i assume the twin pots were not fitted to all variations of the S2. Im thinking i need the Audi 80 S2 Quattro brake pads as these seem to be the dimensions i need but cant tell if it has the springs for twin pots? http://www.venommotorsport.com/product_details.php?id=11941&manufacturer=Black%20Diamond&category=Brake Can anybody confirm this? Any help would be great! :) Also...i know i will most likely need a larger master cylinder, i have read Audi UR Quattro ones are good, but appear to be impossible to find. Does anybody know if there is any others that would work (Car is a non ABS 1990 16v) oh...and im putting a 1.8T in it so must clear the cam pulley? Any suggestions would be great! :) Thanks!
×
×
  • Create New...