doodles

I can supply a braided Hel pipe, TUV/Dekra/FMVSS-106 approved, have a lifetime warranty and come in a range of Colours. Cost is £60 plus postage. My number is zero 797 three 118 seven 48, best calling as not on here that often.

I broke the one above and still have loads of boxes of bits. Also have another that may be getting broke! Drop me a PM with a list and I'll let you know if I have the bits.

I'll get some pics later in the week. It's not where I am and the only time I have during the day to get them will be Thursday.

Rolling Shell I have a J reg red rolling shell project that I was going to put back on the road but change of plans means its now for sale. It was a G60 but the engine, box, loom etc has been used. Still has the doors, bonnet, tailgate, glass, bumpers etc, one wing has a small rust(the only rust on the car) patch but there is another clean wing with it. No interior, but is fitted with a glass sunroof. I will try and get some pics this week as its at a mates in storage. Its located in Grangemouth Scotland and would be viewing only by appointment due to security at the storage place. List Date: 10/26/2014 For more info, click here to view the original listing: Rolling Shell -------------------------------------- On Sale For: ?450.00 -------------------------------------- Mobile friendly version: Rolling Shell Go Mobile: Download the free Panjo iOS app now!

I might have a straight G60 shell with V5 coming up, comes with doors, tailgate, wings, bumpers. Everything really except engine/box loom and interior, some small trim parts are there. A bit far from Somerset tho!

When doing the install there is no need to touch the diag port in the car. It unplugs from the small block connectors at the fuse box. They may have unplugged it!

I have a black drivers wing in good condition, or rust but probably a few scratches in the paint.

Rob, is it these your looking for?

You will probably find the K line isn't connected! The ECU will send a signal via k line and can bus for diagnostics. Regarding rev limiter and not reaching it, the clutch pedal switch will more than likely not be fitted and theses need the or it will hold back. The ECU won't be seeing a speed signal as they probably didn't connect that either! I rewired my mates 24v done by them and the wiring was shocking! The loom was melted and about went on fire!! If your is like his there will be no fuses fitted for the engine harness and half the stuff needed left disconnected. Bare minimum done to get it in and running!

Rob, I didn't get a chance to go look yesterday. Should do today tho.

Pretty sure I have these on a pair of doors off a C I just broke.

I have a 2.9 dizzy engine/box here with chains just been done. £500ono plus postage. I'm in Fife Scotland so probably need a pallet!

I've got one here. I'm in Fife but can courier at your cost. I'm after £30 for it plus postage.

What side do you need as about to cut up/scrap a K plate!

It is L041, I'm in Dunfermline, Fife.

Dougie, I'm about at breaking point trying to juggle everything around! The mk2 is about done and ready to fire it up today but ran out of time! Moving things around tomorrow and the car will be ready to get broken.

Dougie, I will be starting to break this in the next week so I'll be in touch.

I have a black bumper here. £40

I would ship to the states. I'm picking up a set of seats in a couple of weeks for the cloth and will sell the seat belt buckles. Also about to break a 93 Corrado. What do you need for the window set up?

Ok,no worries as its bare doors I have, just what you are asking for, thats why I asked all the questions.

So you can't fit early trims/loom etc to late doors and vice versa?

If it's just the trim that different is the main door the same then? I have two good black doors here but want to make sure they are right!

What is the difference between early and late doors? I've checked part numbers and they are all the same throughout the years! Still trying to get my head around the changes that where made on these!

Forgive my ignorance, but late spec having the window switches in the pocket rather than in the trim itself?

Here is one on a Corrado I picked up last week.