Search the Community
Showing results for tags 'g60'.
Found 7 results
-
Ok so the story so far………………. New Battery (Bosch S5) New Fuel Pump including sender unit Siphoned out all old fuel Clean up of fuel tank New fuel (20 litres) New Spark plugs (Bosch Super Plus) + fogging oil applied to all cylinders Fuel Pump relay connector: Check pin 30 - Constant 12v present Check pin 87 - Signal working towards Fuel Pump when bridged via 30 Check pin 86 - 12v present upon ignition Check pin 85 - "- 0v" reading present upon cranking, which I understand is correct? Fuel Pump Relay New relay installed Proceeded to turn the car but still no explicit/loud sounds of the Fuel pump priming however fuel is being carried upon cranking of the engine, tested via checking fuel line to injectors. Distributor/Spark Plugs Is spark present at spark plugs - No Is spark present on King lead from Ignition coil - No Ignition Coil Removed Ignition coil and correct ohms present when testing with multi meter. Primary coil 0.6 Ohms (must be 0.5 to 0.7 Ohms according to Bentley) - Correct Secondary coil 3600 Ohms (must be 3000 to 4000 Ohms according to Bentley) - Correct Check continuity towards Ignition coil (Green wire) from ECU (Pin 25) - Yes Check voltage to Ignition coil, should be 12v - Yes From this I gather the Ignition coil is "functioning". Hall Sensor Harness Check continuity towards Hall sensor harness (Red/Black) from ECU (Pin 😎 - Yes Check continuity towards Hall sensor harness (Green/White) from ECU (Pin 18)- Yes Check voltage to Hall sender harness upon ignition, should be 12v - No Pin 1 = Ground Pin 2 = Should be under 12v and fluctuate towards 0 when cranking Pin 3 = 12v - No ECU relay connector: Check pin 30 for 12v - Yes Check pin 86 for 12v at Ignition - Yes Check pin 87 for Voltage? Yes on ignition ECU Relay: Connect pin 85 to negative - Yes Connect pin 86 to positive - Yes Does it click, is coil energizing? - Yes If Yes, Connect 85 to negative Connect 86 to positive Check continuity over 30 and 87 with Multi meter - Working ECU Check pin 1 on ECU for 12v at ignition - Yes (Starter power) Check pin 3 on ECU for 12v at ignition - Yes (Fuel Pump Relay) Check pin 12 on ECU for 12v at ignition - Yes (Injector Power) Check pin 14 on ECU for 12v - Yes (Power from Control Unit Relay) Check pin 22 on ECU for 12v at ignition - Yes (Idle stabilizer valve) Check pin 25 on ECU for 12v - Yes (To Ignition Coil) Fuel Pump Relay: New relay installed, Continuity present, Voltage present. Pump still not priming Ignition Coil: Continuity present, Voltage present. Hall sender harness: Continuity present, no Voltage present - should this be coming from the ECU? ECU relay: Working as far as I can see but will change for a new one as it was already on order and in the post. ECU: All checked pins receive inbound voltage, however I have no further points of reference to check whether the ECU is distributing the signal to the various components. In addition still no Tachometer readings along with fuel on dash. Does all this point to a faulty ECU? 😐 Any suggestions or corrections welcomed Kr Dee
-
Evening all… Completely new to the VW scene however I finally managed to pick up a long outstanding 92 plate G60 a few weeks ago. It has not seen the light of day for around 12 years at least so this is going to be a fun ride. Lots of history around the car so it may well be one that someone may have spotted it a number of years ago in the edition38 scene. The list of work has begun but have already hit a few bumps along the road so I am sure I will be frequently posting my woes and questions… apologies in advanced 😀 Regards Dee
-
As per my first post with the lumpy idle I bought the car back in early April. I looked at it on the classifieds for a few weeks and decided to take the plunge. It is the dream car of my youth which I never ended up buying for some strange reason. Purchased with my eyes wide open with the lumpy idle and I know it needs some bodywork doing (best mate will do the bodywork for me) - needs passenger door (any contacts or leads would be welcomed) as it is starting to rust at the bottom, the NSR side sill needs repairing and has a bit of rust on the rear panel inside - I think relating to water ingress from the badge? and alloys need refurbishing. After doing my research the good bits I picked up on are the car is totally bog standard (exception of a Magnex exhaust fitted by AMD a few years ago) with a clean interior (side bolster is sagging but will get it re-done) and sunroof works well, ABS seems fine and spoiler works at speed but the override button isn't working - on my list of jobs to look at. It's had 2 owners (110K miles) and the guy I bought it from has had it 25 years and has all the annual service records starting at main dealer and then onto AMD and local German auto care company. I've also got original invoice for the car. Plan is to start the refresh process over the next 18 months or so to get it back to its former glory and enjoy it.
-
Original BBM RSR supercharger outlet kit for G60. Bought from Only Charged Dubs in November 2018 but never opened. All items in the kit are still in the plastic packaging they were delivered in. Kit includes machined outlet with bolt, black silicone hose, black tube and both clamps. £150 including uk postage.
-
So Ive has a problem with my car and the way it runs, as it gets up to temperature it goes from running fine to really lumpy and black smoke out the exhaust. I have to rev it a little to keep it from stalling. today I went to move it and it did it before the oil temps even registered and the water temps had nearly risen. ive unplugged lambda sensor with no change, replaced blue temperature sensor with no change, the distributor was refurbished not so many miles ago and a new coil fitted. I’m in the process of Replacing the battery earth but could it really be that alone? how can I check Ecu?
-
Hello, I looking for a G60 grille badge in good condition with the clips intact. If you can help, please pm me. Cheers Karl
-
Simples as it says on the tin.....need a new radiator.....its a 1991 G60 so which should I buy? Am confused some are saying can use a normal one for the 16v but I am not so sure? Fankies for any advice mwwwwwwwwwwwaaaa
