Hi my drivers side heated seat does not work, the dial switch seems fine and the passenger side works, i have checked the heated element in the seat and the wiring to the seat but cannot find fault?
Hi .
I've a 1993 fitted with heated seats but not wired and no switch in car.
Where was switch positioned ?- and is it easy to wire up or a big job.
Is there 2 switch - 1 each seat or one switch suits both ?.
Tks
Pj
I have had my G60 now for 17 years. it was parked for the past 10 years. since bringing her out again i have managed to change almost everything - every pump and pipes and most of the sensors.
i have changed the water pump, new thermo, expansion Tank and cap and also changed the matrix along with all the pipes. Changed the blue sensor too.. car runs fine but my fan does not kick in until 110 on the dash and cools it down, however, my internal heater is blowing out cold air - WTF. i have change
Bought it from stealth a few months ago for £225 only had 500 miles use, comes with extra hose and metal bracket. Only selling as I have sold the rado. Send me your offer, cheers Jay.
I bought my '93 Corrado VR6 in May 2017 - with very little knowledge of the car and the engine.
After speaking to friends who have an interest in VW cars, I found out that the engine is not an original Corrado VR6 engine, it was out of a MK3 Golf. The engine bay has also been partially smoothed (badly) so there are things that are missing from the bay. I say badly because the air filter was behind the engine and above the exhaust manifolds.
[ATTACH=CONFIG]92959[/ATTACH]
Our assump
25th May 2017
Fitted '16vDaves' shortshifter
1st June 2017
Replaced the drivers door card
Fitted '16vDaves' handbrake tunnel bracket
Fitted good condition used centre trim
25th June 2017
Fitted new fuel pressure distributor
Set fuelling and idle speed
Huge difference in fuel economy!
3rd July 2017
Oil change (145,000)
New spark plugs
New coolant expansion cap
19th July 2017
New oil cooler
New oil filter housing gasket
New oil sump and seal
New sum
24th November 2016
New gearbox mount
New rocker cover seals
New starter motor
New clutch slave cylinder
25th November 2016
New LUK clutch kit
New release bearing
New crankshaft seal
New flywheel bolts
New clutch bolts
8th December 2016
New lower control arms
New inner roll bar bushes
New roll bar drop links
Anti roll bar sanded bare and re-sprayed
New ball joint nuts and bolts
Crossmember sanded and re-sprayed
Crossmember cover plate sanded and re-spra
5th May 2016
Replacement sunroof headlining panel cleaned and fitted
Headlining replaced with new foam strips
Made a cup holder to fit in rear ashtray
29th May 2016
Fitted standard manifold and down pipe (from a 33,000 mile car)
Fitted new exhaust gaskets
New exhaust manifold brass nuts
Fitted stainless exhaust
Fabricated a flexi with twin hangers to join down pipe to centre section and make a better fitting system
Poly hangers
Fitted radiator cover and holding bracket
11th November 2015
Replaced all windscreen scuttle trim and blower box cover
Fitted passenger under dash shelf
Fitted drivers side under dash fuse box cover
15th November 2015
Fitted new injector seals
Sprayed radiator cover plate
Degreased the head while manifold was off
New inlet manifold gasket
Throttle body cleaned
Refurbished 50mm inlet manifold fitted
23rd November 2015
Changed front and rear shocks to Bilstein B4's
Changed front and rear springs eibach 30m
Hi all anybody got any ideas on my heater problem on 1.8 16v, it blows warm air for a short time then cold new to this so not sure where to start. Thanks
Over the weekend I fitted a Powerflex front engine mount insert. Another transformation in driving. I recently heard a small clunk on acceleration and noticed a bit of engine movement so decided to go the Powerflex insert route for the grand sum of 41.00. I have done a big journey in the car and it feels so much nicer, tighter and no clunks. If you go this route note that my installation did not have the lower big washer that is suppose to hold the engine down. I had to temporarily reuse t
Hi folks. Im looking at replacing the exhaust system on my 1990 1.8 16v. Im thinking about the complete jetex system but i need advise on the downpipe. My original is just that original and is starting to blow. My main question is what downpipe can i fit that would go onto the jetex system . I would like to gain a few more bhp if possible. Im on a very tight budget so if anyone has or knows of any avialable get in touch,
thanks guys
Alright folks. Having a bit of a problem. I bought a vr6 about 2 weeks ago and for the last 4 days roughly its been slightly juddering under load but only in low revs. Very slight judder when accelerating. Also when it gets to the high revs there's less power than normal and I can feel the car trying to slow down even with my foot to the floor and it doesn't pull or have near as much power as normal. Ive changed the oil and plugs and fuel filter and still no difference. Really need help guys. An
Just bought a VR6 with this registration and was wondering if anyone would be interested in the plate and what it would be worth as I would prefer to return her to her original L plate.
Hi people. Having an issue with my valver. Has run perfect for the past two years. However the other day its started to judder and struggle to keep going and ended up kangerooing down the road. Once stopped the fuel pump became very noisey and almost cut out with the revs dropping. I have since changed the fuel pump and checked the lift pump in the tank. All the fuel lines have been cleanedto. The car started fine after repreplacement and ran perfect at idle. The original fault still exists.
