somersetdub 0 Posted February 3, 2018 Hi all, I am looking for a decent Vr6 engine, with low miles or rebuilt etc.. I really only need a decent bottom end, but will purchase an engine complete. Thanks Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
VEEDUBBED 0 Posted February 4, 2018 Well, i still have an ABV bottom end with only 19.000km's run.. Any good? Only problem is that i'm across the pond from you. Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 4, 2018 Cool.. Where abouts are you and how much are you after? Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
VEEDUBBED 0 Posted February 4, 2018 Send me your email and i'll get you a load of photos sent. What's wrong with your engine? Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 4, 2018 PM sent Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
VEEDUBBED 0 Posted February 5, 2018 Got it. I sent you another PM with a bit of history. Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 6, 2018 Any others about? Want to keep my options open! Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
Geeba 0 Posted February 6, 2018 Whats wrong with your block? Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 6, 2018 The intermediate shaft snapped on the one in my car and starved it of oil.. I had a spare 2.8 AAA engine from my friends car which was a nice engine, but unfortunately he rolled the car and when I stripped the engine down I found that too had suffered from oil starvation when it was rolled and killed the big ends and scored the crank. So basically I have two engines which have both been ruined due to oil starvation! I just need a decent bottom end really, I have a good recon head from my engine. Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 6, 2018 Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 6, 2018 Gutted!! Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
Geeba 0 Posted February 6, 2018 Didn't you go forced induction? Quote Share this post Link to post Share on other sites
Geeba 0 Posted February 6, 2018 Strip it down... get it hot tanked, get the crank ground, new bearings and rods, hone and new rings, low compression pistons. That way you know its good. second hand lumps are always an unknown. Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 6, 2018 I would rather find a decent known good engine after being let down by my fully rebuilt engine. Plus it’ll be cheaper. Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
VEEDUBBED 0 Posted February 6, 2018 Did you get the photos? Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 6, 2018 No... I’ll double check my email.. Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 8, 2018 Bump Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
Geeba 0 Posted February 12, 2018 https://www.ebay.co.uk/itm/222834047890?ul_noapp=true 500 notes... Quote Share this post Link to post Share on other sites
somersetdub 0 Posted February 14, 2018 Send me your email and i'll get you a load of photos sent. What's wrong with your engine? Hi Andrew, I have just emailed you again regarding your engine... Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
VEEDUBBED 0 Posted February 14, 2018 Didn't get it mate. Still haven't found anything yet?? Quote Share this post Link to post Share on other sites
Geeba 0 Posted February 16, 2018 Bag of sand! https://www.ebay.co.uk/itm/253429702074?ul_noapp=true Quote Share this post Link to post Share on other sites
