gollfy

Thanks for the info regarding 00516, going to check condition of them when we have better weather... :? Don't suppose you know what kind of voltages etc I should be getting? As for the knock sensor, Im 100% certain an HT lead has the pickup ring on.

After power washing my engine off which was not the bright idea I thought it would be, my 16v seems now after a few days seems to be running like a bag of spanners :( Since I have had fault codes from ecu 00516 Closed Throttle position Switch - F60 Open circuit/short with power No Idea about checking this one, anyone help? (where/how) 00525 Oxygen sensor - G39 No Signal Error occurs intermitantly Going to check connections near engine mount for voltage etc 00540 Knock Sensor 2-G66 No Signal Error occurs intermitantly No Idea about checking this one, anyone help? (where/how) Any idea's about the above would be gladly appreciated. I'm not wanting to spend vast amounts of money at this as it isnt really in tip top condition wise. Also what does F60/G39/2-G66 Refer too? Thanks all

Just over a year old by 1month, originally from gsf :( arrr well off to gsf it is again 8)

Hello all, Just noticed a patch of fluid under my car :( , seems to be coming from the clutch slave cylinder. I had one fitted about a year ago :( If I have fluid leaking from there, does this mean I need another one? or a new seal? Thanks all

My 16V has started to run like a bag of spanners :( If you drive it really steady, it runs perfect. However when you put some gas on e.g (drive normally), after about a couple of minutes it starts missing. I have changed plugs leads dizzy cap and rotar arm On inspection of the new plugs, after it did not solve the problem, they are really black :( and its drinking fuel Can I presume that this is down to over-fuelling? If so where do I start to resolve it?

What colour wire has it got going to it? red/yellow by any chance? Is this the wire that goes to the dash temp guage? Thanks for your help 8)

I have a 1992 2.0L 16V corrado and the temperature guage does not work, and Im running blind with only the oil temp as a guide. I have checked the condition of the wires and they seems ok and they are all connected Is there a simple way to check the temp guage without taking the dash clocks out? I know there is 3 or 4 sender units and how do I check these? Thanks all

Ripped from another forum I use Link does work, getting hammered at the moment as lots of peeps reading it from different forums. Gollfy is from when I used to have VW golfs naturally and I have just kept my username the same:)

http://www.vx220.org.uk/forums/index.ph ... pic=54660l Worth a read :lol:

I have just aquired a set of interior and the rear seat does not have a bump/arm rest in the middle for the first aid kit?, is this just an interior from an 8V or was it installed in various models?

I am after abit of advise for my 2.0 16V. The temperature gauge is not working :( Anyway to test if its the dash at fault? Also if it is, would I be able to replace the left dial (temp/fuel) instead of replacing the whole pod. Does the passat dial fit also? Any help appreciated. Thanks

I believe there was around 213 8V Corrado's (maybe wrong) so they are definatly rare, although they are of the least disirable as they are are abit performance lacking. They have the ADY code engine in which is exactly same as the MK3 Golf gti but that engine was only used between the years 1994 and 1995 and the majority of the parts from the Mk3 Golf Gti will fit straight on. I have one and I quite like it but its a bit sick at the moment and I get about 30Mpg but I know that if you drive it right you can see close to 40Mpg. They also fitted the engine in the passat/sharan/vento and I think in some seats 8) No mods on mine at the moment :( my G60 see's to that

I have aquired a cylinder head to go onto my 8v 2.0 rado (ADY engine code) as it seemed to like burning oil. It has the part number 048 103 373 and I was told it was off a 2.0L golf or a passat. Dont know whether its a 2E/ADY/AGG Code? I need to know if this will fit and what its off originally. Thanks all

Mine is kn@ckered :cry: would it be the same one that is on the mk3 golf gti or is it the same on thats on the 16v rado

Think I have already asked this question but want to be sure before I part with any hard earned cash. The g/f's Corrado 2.0 8V seems to be losing/burning more oil than the Exxon Valdez :cry: . It's only done 97k so am going with the oil seals being kn@ckered. Now the engine code is ADY and after a bit of research, that particular engine was used in the following vehicles Vento 2.0 95-98 Passat 2.0 94-96 Sharan 2.0 95 on Toledo 2.0 95-99 Ibiza 2.0 95-98 Alhambra 2.0 96 on Cordorba 2.0 96 on Golf 2.0 94-95 Now I have been offered a couple of cylinder heads, one being from a 2.0 vento (not sure of year) and the other from a 92 MK3 Golf Gti. Now all they can tell me is that the engine code is 2E for the Vento and Golf. Although these heads will have a different engine code.(i think) Will I be safe fitting one to my Corrado? Thanks again Dave

A big thanks 8) for your help

Thanks Neil Just need to know where to put both my probes :roll: ooeerrr as I'm not an electrician

I need to check my lamda/oxygen sensor is working as MOT time is looming :cry: and it was a slight problem last year but MOT bloke let it through luckily for me. :D I've searched the forum for the info but cant find it, but can remember someone telling me last year. Thanks all.

thinking about this but no pics of inlet side :( http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... &rd=1&rd=1 So not all MK3 Golf GTI heads are the same?

bump

Does the head off any mark3 golf gti fit my rado or do I have to try and get a 94/95 Golf GTI head of the same period as my rado as my car has a siemens ecu which was only used on 2.0 vw cars years 94/95. I know they are all pretty simular, just need to make sure Thanks all.

Can anyone tell me where the auto ecu is located and where the reverse light wires are in the auto box loom. I have a 8v which has been converted to manual and need to remove auto ecu and make reverse lights work :-P cheers all

voted!!! still behind a volvo??

I have a standard 1995 2.0 8v rado and just need to know the size of the brake discs that fit it:) are they 280mm? Thanks all

Cheers walesy 8)