dumptyboy

No problem. I will PM you shortly. Rob.

I've got them in chrome with the standard lenses. I will be putting my standard headlights back on for mot time though. This is the only pics I've got unfortunately,

I'm needing these aswell so put me down for a full set if any become available please.

It's just the one at the end of the cable that needs a grub screw ( the end behind the passengers headlight. I had the same problem as you after fitting a new cable and I tried adjusting it several times and it would only pop one side. I ended up spraying loads of wd40 on the release mechanism and the part on the bonnet with the spring and it's been fine since. Don't know if that will help you though mate?

Here you go Nick. Sorry about the rubbish pictures: £12 posted if you still need it.

LC6v green pearl. Cheers.

Sorry the ISV has sold. The car is 1993. It's the 9A engine with a late grey interior. I do though have an early mirror adjuster switch, let me grab it and check its condition and I will message you back. Cheers. Rob.

I have both mate, pedal box and master cylinder. I will have to double check the condition of the master cylinder as I have a couple and know one has a faulty seal, but it will take me minutes to double check which is the working one. Pm me with an offer if you are interested. Cheers. Rob.

Yes mate no worries, I somehow missed your message yesterday. I actually have another loom in my shed with the wiring you need. I can sort you out with that no problem. Send me a PM if you are still interested. Rob.

£15 posted for the lines and the relay? I would try and do it cheaper but the fuel lines will probably need to be in a fairly longish box even once I coil them up to avoid kinking, and post offices don't like big boxes unfortunately without paying over the odds! Let me know what you think. Just to let you know I also have a fully working wiper motor if you end up needing one. Cheers. Rob.

I've got a pair of G60 fuel lines and a wiper relay. I'm not sure though if one of the fuel lines has been cut on the fuel filter end ( I don't remember cutting it though)! Perhaps you can compare them to your and let me know. Engine side: Filter end: I will did a relay out aswell if the fuel lines are any good? Rob.

Pictures of the fuel pump and splitter for you mate. I've only just removed them off the car so haven't had a chance to clean them yet. The photos mate the pump look worse than it is, so I will add better pictures once I clean it if you like. The splitter has a small crack on one corner right underneath and a couple of light scuffs on the underside also, but it is in great condition other than that.

What engine is it?

Are the heater controls functioning correctly? What im trying to say is are the controls moving from hot to cold regardless of what the controls say? Does that make sense?

Payment sent.

I will remove the wiring looms tomorrow afternoon and try to label them up as best I can so that it makes it obvious where they go to. I will take a load of pictures and hopefully you will see what you need. Its possible your spoiler module is knackered if the spoiler doesn't rise at speed? I have this available also if you want to try that out. Does the spoiler rise on the button on the dash? I will update the thread tomorrow for you mate. Cheers.

No worries mate. ;)

Hi Brett. Yes £60 posted would be fine. The metering head is fully tested and works perfectly. Send me a PM with you address and I will send you my Paypal details. Thanks mate. Rob.

Hi Dave. Im in the middle of removing the dash and wiring looms as we speak. I was going to sell the complete dash looms from the fuseboard and sell them individually. They are all uncut and still have the foam sleeving around them. Would you be interested in buying the complete set? Im more than happy to sell the ABS loom seperatly if you wish though. I ended up replacing the complete loom on my VR as it had a loom fire behind the dash and ended up removing the dash and replacing the lot! The loom I have would be ideal if you need a full replacement. Let me know what looms you need etc, and I will get back to you. cheers.

I'll take the second pair of window rollers please.

Haha, yes a wobble bar. Not to be mistaken with a Wonka bar. ;) I had barely any tools about 12 months ago and bought a G60 that I broke for parts as it was beyond repair, the money I got back from breaking it I went and bought tools with. Having the right tools for any job is important and if you look after them they will last a lifetime... That wobble bar has saved my knuckles more than a few times on my VR. :)

No probs mate. As soon as I get home tomorrow afternoon I will get back to you. I will be adding a load of other bits aswell, so just let me know if there is anything else you need. cheers.

I did this same job the weekend before last JEZR. The straps look so much better than the old rusty ones. I had the same problem with the rear bolts and used a wobble bar on my ratchet and it worked a treat. It probably took me longer to re-attach the new brackets as they need bending into shape. Once installed I realised the drainage type holes were offset so had to remove them again as my OCD wouldn't let them remain in place until they were perfect, haha. ;)

Could you post up a picture of the thermostat sensor housing cover please? I think this is an item I've been looking at getting for a while. Cheers mate. Edit: is that it in the second picture?

No worries mate. If there is anything else you need then let me know. Cheers.