VR6 Parts, updated 31.3.13

[MattPc 0]

I have a few VR6 parts as I am clearing out, whist also converting to OBD2.

All parts are in good working order unless stated. Items are + postage or collection from Braintree.

 

1, VR6 OBD1 over bored throttle body, welded underneath to add wall thickness. It has a direct acting butterfly rather than a ratio butterfly from factory, Sold

 

2, VR6 Catalyst, has a weld on the underside, mating surfaces cleaned, in good working condition, Sold

 

3, VR6 airbox inlet plate, the bit that sits behind the headlight, £5

 

4, Set of coil pack HT leads in black, £20

 

5, Bosch starter motor, Sold

 

6, VR6 manifold heat shield, £10

 

7, Fuel rail, £5

 

8, Dual tone horns, rusty, Sold

 

 

9, 288mm Fabia VRS front calipers, carriers, pads, hoses & discs, sold

10, Jetex stainless steel exhaust cat back system, 3 years old, the underside of the system is nice and shiny, top of the back box still has some of the protective cover on, the dark bits in the picture. it comes with an adapter to mount to the standard CAT. includes three new exhaust clamps. Sold

11, Master cylinder with reservoir, £20

12, Brake servo with position sensor, £45

13, Manual pedal box, £20

14, 2 sets of standard VR6 injectors, £10 per set

15, Thermostat housing & thermostat, £5

16, Power steering pump & reservoir, £30

17, Alternator/ AC compressor/ PS pump bracket, £5

18, Inlet air pipe to TB, £5

19, 15" Space saver wheel, £10

20, Idle stabilization valve, £20

21, Valeo Clutch & clutch plate, covered 35k on a standard engine, £20

22, 02A CCM gearbox, 107k miles on a standard engine, £50

23, New front brake dust shields, Sold

24, New rear brake dust shields, Sold

25, 3 bar fuel pressure regulator, £10

26, 2x Auxiliary belt tensioner, £15 each

 

 

27, 4 bar fuel pressure regulator, £10

28, 2x Coolant header tank with cap, £10 each

29, OBD1 throttle body, £15

30, Water pump pulley, £3

31, Steering colunm UJ bulkhead gaiter, £5

32, Standard 12V VR6 flywheel, ideal for lightening or replacement, £10

33, VR6 fuel lines, tank to fuel rail, with filter carrier & filter, £10

34, Charcoal canister valve with pipe to TB, £5

35, Radiator fan controller module, £3

36, Rear engine mount aluminium exhaust heat covers, £10

37, Standard VR6 cams, both 2.9 & 2.8 sets available, £10

 

 

I'll add some more parts later on.

Any questions please ask

 

Regards

Matt

Edited April 22, 2013 by MattPc

[RadoVirgin 0]

I'll take the throttle body!

[science 0]

Hi Matt, can I take the Cat and the Starter please, may possibly need postage.

[MattPc 0]

RadoVirgin, PM replied to regarding payment.

 

science, I will be down in Basildon on Thursday 28th if that helps with collection, if not a 24hr courier would be £10.50

 

Matt

[RadoVirgin 0]

I don't seem to have a message from you in my inbox

[science 0]

science, I will be down in Basildon on Thursday 28th if that helps with collection, if not a 24hr courier would be £10.50

 

Matt

Thanks Matt, could you courier them please. Just let me know payment details, cheers.

Neil

[MattPc 0]

RadoVirgin, payment received, thank you.

 

science, PM'd you payment details.

 

Matt

[MattPc 0]

RadoVirgin, TB posted this afternoon,

 

Some more parts added to the first post.

 

Matt

Edited March 26, 2013 by MattPc

[pastmann 0]

Hi Matt,

Can you get a delivery cost on the calipers+carriers, pads, hoses & discs, to ML85PG

 

Cheers

Dave.

[MattPc 0]

pastmann, delivery to ML85PG will be £14.50

 

Matt

[pastmann 0]

Cheers Matt , I'll take them.

PM with you details.

 

Dave

[MattPc 0]

pastmann, The brakes will be collected on Tuesday due to the bank holiday.

 

I have also added some more parts to the list.

 

Matt

[Benjevw 10]

Hi mate

Are the cams from a 2.9?

Cheers

Ben

[sankysvr6 0]

Hi will the exhaust fit a G60? Or do you have part number for it so I can check myself.

 

Also could offer postage if it does fit.

[MattPc 0]

Ben, I will measure the cams I have as I am sure that I have both 2.8 & 2.9 spare sets.

 

sankysvr6, The kit code is 26-H7TR system. I have checked on the Jetex website and that also confirms that the systems fits both the VR6 & G60, and I can box it up and send via a courier.

 

Matt

[pastmann 0]

Matt,

 

Cheers those Calipers + Discs arrived Wednesday.

 

Thanks.

Dave.

[karmannski 0]

New front&rear brake dust shields

Will they fit late type vr6?

If yes will you let it go £50 delivered to NR32?

[srp 10]

hi

 

have you got the top part of the standard air filter box for sale

 

stephen

[MattPc 0]

Sorry for the late replies everyone.

 

Hi mate

Are the cams from a 2.9?

Cheers

Ben

 

I have checked and I have both th 2.9 and 2.8 spec cams, which ones are you after?

 

 

New front&rear brake dust shields

Will they fit late type vr6?

If yes will you let it go £50 delivered to NR32?

 

Yes they will fit the late VR6, I have somebody else interested in the front dust shields, I will await a reply on weather they take them.

 

 

hi

 

have you got the top part of the standard air filter box for sale

 

stephen

 

Funnely enough I do have a spare top half of the VR6 airbox, £10 + £3.50 postage sound ok.

 

 

Matt

[Benjevw 10]

Hi mate cheers. I'm going to leave them for now as plans have changed!

Cheers anyway

Appreciate it

Ben

[srp 10]

Matt

 

thanks for the reply and will have the top half of the air box.

how's best to pay you?

 

Stephen

[MattPc 0]

srp, Payment details sent via PM

 

Matt