Jump to content

mrbeige

Legacy Donators
 View Profile  See their activity

  • Content Count

    3,332

  • Joined

Everything posted by mrbeige

  1. mrbeige
    Welcome to THE forum 8) Nice motor! 8)
  2. mrbeige
    Welcome dude Nice VR 8)
  3. mrbeige
    I like 8) loads quickly and is straight forward! I do have one comment though.... I'd be consistent with you font you use for the main body text. I'd stick it all in the same font as the introduction, including the product desriptions. What do you reckon?
  4. mrbeige
    Why not get you original seats re-trimmed in black leather, which could be a cheaper option. Or Porka seats, normally aren't too expensive, and often fully electric. As with the TT seats you would need subframes, but there are quite a few people who have fitted Porka seats, whop might share the knowledge....
  5. mrbeige
    I had a similar problem with mine. Check your distributer and particularly the hall sensor, and that its not touching any part of the bit that spins around (for want of a better explaination!). I'd changed my rotor arm at some point and managed to bend that part and it would catch on the hall sensor inside the dizzy, causing the engine to randomnly die. Worth a look?
  6. mrbeige

    UR Quattro

    mrbeige posted a topic in General Car Chat

    Found this on streetfire.net.... 8) 8) 8)
  7. mrbeige
    Black, definately! 8) And as a plus, they wont look as dirty as quickly...... 8)
  8. mrbeige
    It's massively satisfying, no matter how small a job it is!
  9. mrbeige
    Cheers guys, loads that I want to do to it, just finances not allowing at the mo.... :(
  10. mrbeige
    I run 9's all round, and do get a bit of tram-lining, but you get used to it! My Koni's are set full hardness too, so ride quality isn't fantastic.
  11. mrbeige
    Nice job dude 8) What type of glue have you used to stick the suede on? Just normal spray adhesive?
  12. mrbeige
    Was gonna knock them out for 40-50 quid. Fitting wise, would probably take 1.5-2hours in total to do, I guess. The fiddly bit is fitting the LEDs in the instrament cluster. I could fit it for you if you like, but it's a bit of drive from Bristol :lol:
  13. mrbeige
    That's the same as mine, and I've got a 2.0l 16v......
  14. mrbeige
    The cheeky beggers. You should be complaining to them about how much its costing you!
  15. mrbeige
    Not got a VR, so not sure what there is in those 4 positions There is an option for just one 10mm LED output, or possibly just an output driver for a proper dash mounted shift light.
  16. mrbeige
    Looks bloody nice that does 8)
  17. mrbeige
    Cheers :thumb right: Its my oil cooler,don't want to damage the core while its been tossed about. Oh I see! Thought it might be something secret :lol:
  18. mrbeige
    Looking good. 8) Whats the cardboard covering up?
  19. mrbeige
    Cheers dude. The eyebrow I got free, so not really a choice, but I like it.
  20. mrbeige
    To be fair that looks smucking fart! Super smooth and some serious work gone into that. Fair play 8) 8)
  21. mrbeige
    Pretty much!
  22. mrbeige
    Did you want to put the LEDS where I've put them then? Doesn't take much doing to be fair, just some glue gun action!
  23. mrbeige
    Right couple of changes so far. Replaced the grey dash with a black one now, just need to sort the toledo heater controls. And I've done my own custom shift light. Here's a quick vid!
  24. mrbeige
    Done it! Here is a little clip of it in action! (taken by the missus on her phone)
  25. mrbeige
    I didn't mate, but it is in the bottom left hand side of the PCB. I'll try and get a pic of it next time I take the clocks out.
×
×
  • Create New...