pbradley98

Superb - thank you. Looks like I'm missing the rhs one so will have to rummage through my box of random bits of trim to see if it's ended up in there at some point!

Hi, hoping that someone may be able to advise if I'm on a wild goose chase or not! Have recently fitted a DAB radio and just got round to replacing the factory aerial with a new beesting DAB aerial, so had the headlining out to run the wiring properly. Whilst it was out decided to give the headlining a clean up, which meant I needed to do the sunroof interior panel too as otherwise it would have looked rubbish! So here's the question - a black piece of trim came out during this process and I have no idea where it's come from / what it's actually for! It's part number 763684959 (image below), but I can't find it on a parts diagram anywhere for the Corrado sunroof, it only seems to be referenced on a Polo! I only seem to have one and can't see it's opposite part anywhere, as I assume it's "sided" and there should be a mirror image for the other side.... Thanks in advance to anyone who can advise on this (especially if it's important for the sunroof continuing to tilt and slide!).... Cheers, Phil

Hi Do you have the front offside wing and if so what sort of condition is it in? Thanks Phil

No - there are two variations - early with a three pin connector on the motor and late which have a different harness connector but I can't remember the specifics of the late connector. I think you can fit an early motor to a late panel, but not the other way round....

Finally got round to doing this, having bought a set of Sprinter's reproduced foam liners several years ago but never getting round to fitting it! Not too bad all in all, took about an hour to quickly scrape of the foam, then used a cloth to rub white spirit into the residual glue / foam residue layer and scrape off with a credit card to get back to pretty much pristine paintwork underneath (if only the same was true of the topside of the bonnet, which is definitely due a respray!). Then it was just 5 mins to actually fit the replacement foams - what a difference not to have crumbling, patchy foam!

Really helpful post - thanks!

Don't do it! The value of a car like this is only going one way these days....

I don't think there are many that fit the Corrado because of where the seat belt comes out of the chassi - I've got two of these which fit really nicely into the back of the Corrado - recommended by a few people on here. Not cheap (£90 at Halfords at the moment) but they should last until they are no longer needed, as they start as a five point harness, then you can remove the harness and use with an adult belt. My girls are still in these at 6 and 4....Hope that helps. http://www.halfords.com/kids-zone/car-seats/toddler-car-seats/britax-romer-evolva-1-2-3-child-car-seat

Looks good - I'll go for this. If you could pm me payment details.... Cheers Phil Sent from my C6603 using Tapatalk

Interested - any pics? Thanks Phil Sent from my C6603 using Tapatalk

My daily, coming up to 12 years now and 92k, so around 7.5k a year - that said I cycled to work for about 6 years of that! Should break the 200k mark in a couple of years! Sent from my C6603 using Tapatalk

Ditto! Sent from my C6603 using Tapatalk

Hi I'd like a late VR set please. Pm sent. Cheers Phil Sent from my C6603 using Tapatalk

Thanks for the replies all. It's split from the section that pushes into the channel, so I'll see it the one from heritage is any good, as I think I'd need an awful lot of sealant to hold it down! Cheers Phil Sent from my C6603 using Tapatalk

Hi, My outside windscreen trim also needs replacing - I assume you can replace it without removing the windscreen? Can anyone advise how this is fitted - is it just a push fit or do you need to use a glue or sealant to hold it in place? I've (tried to) attached some pics to demonstrate the need! Cheers Phil Sent from my C6603 using Tapatalk