288mm front brake upgrade hoses

[Keyo 47]

Hi, 

Has anyone got a link for the front brake hoses I need for the 288 mm upgrade- good brands please and stainless steel if possible. 

 

Cheers. 

[Dox 23]

FRONT HEL Brake Lines For VW Golf MK3 2.8 VR6 Discs / from ch 1H-SW560 001 92-97 | eBay

[Keyo 47]

9 minutes ago, Dox said:

GOODRIDGE STAINLESS FRONT BRAKE HOSE (PAIR) VW GOLF MK3 WITH M10 FITTING HOSES | eBay

Thanks Dox, 

The pads are they the stock ones for 96-98 mk3 vr6 for the 288 mm pads ?

Cheers. 

 

[Keyo 47]

12 minutes ago, Dox said:

GOODRIDGE STAINLESS FRONT BRAKE HOSE (PAIR) VW GOLF MK3 WITH M10 FITTING HOSES | eBay

Ate both the manufacturers  hoses the same design chap the 2 links you gave same end fittings ? 

Thanks 

[Dox 23]

Or MK4 , TT etc

[Dox 23]

1 minute ago, Keyo said:

Ate both the manufacturers  hoses the same design chap the 2 links you gave same end fittings ? 

Thanks 

???

[Keyo 47]

Just now, Dox said:

???

The fittings look different on the two brands of hoses I cant tell picture is bad on Good ridge ones on advert. 

[Dox 23]

Sorry, deleted that link now

[Dox 23]

1 minute ago, Keyo said:

The fittings look different on the two brands of hoses I cant tell picture is bad on Good ridge ones on advert. 

They were the wrong ones, you need banjo fittings for the 288mm upgrade

[Keyo 47]

6 minutes ago, Dox said:

They were the wrong ones, you need banjo fittings for the 288mm upgrade

Ok great so its the Hel ones I will get - cheers. 

[fendervg 32]

There are two different types of 288mm callipers, one with banjo fitting, one with a screw fitting, and different cylinder sizes - so watch out:

From VR6 Golf3, banjo fitting

3A0615123 calliper with 54mm pistons lh

3A0615124 calliper with 54mm pistons rh

 

From Passat,screw thread

4A0615123A calliper with 57mm pistons lh

4A0615124A calliper with 57mm pistons r

I've never seen the Passat ones in person, I bought new Mk3 ones from VW when I did mine, and used the Goodridge braided hoses with the banjo fitting.

Both types are ATE.

[Keyo 47]

Oh right will have to watch that then. 

[Dox 23]

1 hour ago, fendervg said:

There are two different types of 288mm callipers, one with banjo fitting, one with a screw fitting, and different cylinder sizes - so watch out:
From VR6 Golf3, banjo fitting
3A0615123 calliper with 54mm pistons lh
3A0615124 calliper with 54mm pistons rh
 
From Passat,screw thread
4A0615123A calliper with 57mm pistons lh
4A0615124A calliper with 57mm pistons r
I've never seen the Passat ones in person, I bought new Mk3 ones from VW when I did mine, and used the Goodridge braided hoses with the banjo fitting.
Both types are ATE.

These are the ones found from your part numbers, note the shoulders are square, these I believe are mk5 type callipers


These are Mk3/4 note how the shoulders taper?


Sent from my iPad using Tapatalk

Edited June 3, 2021 by Dox

[Keyo 47]

So I got this from a mk3 breaker fir £59 - take it they are the correct ones - they look gross - you all reckon big redd can make them good again . 

Do big Redd put new sliders and pins for the the pad carrier. 

Edited June 5, 2021 by Keyo

[tonedef 9]

Big Redd send them back looking like new, seals, pistons, guides, sliders, the lot! The only piece they didn’t replace apart from the obvious calliper body was the spring.

 

[Keyo 47]

2 minutes ago, tonedef said:

Big Redd send them back looking like new, seals, pistons, guides, sliders, the lot! The only piece they didn’t replace apart from the obvious calliper body was the spring.

 

Ok thanks mate they look good  - is it worth taking the springs out before I send them to them - cheers. 

[tonedef 9]

Just now, Keyo said:

Ok thanks mate they look good  - is it worth taking the springs out before I send them to them - cheers. 

I think they ask you to remove all loose parts before you send them anyway. So yes 👍

[Keyo 47]

Just now, tonedef said:

I think they ask you to remove all loose parts before you send them anyway. So yes 👍

Ok great - thanks 

[Dox 23]

They do look like MK3, notice how rusty the pistons are. I'd remove the banjo bolts before shipping, there's 2 types of thread pitch and you can use them to make sure you have the correct ones in your hose kit.

[Keyo 47]

35 minutes ago, Dox said:

They do look like MK3, notice how rusty the pistons are. I'd remove the banjo bolts before shipping, there's 2 types of thread pitch and you can use them to make sure you have the correct ones in your hose kit.

Thanks all all ready have the banjo bolts stashed . 

[Cressa 44]

They will come back looking mint.

Can you see if there is an anti rattle plate fitted at the carriers where the pads sit . I always wondered whether these should have them?

[Dox 23]

50 minutes ago, Cressa said:

They will come back looking mint.

Can you see if there is an anti rattle plate fitted at the carriers where the pads sit . I always wondered whether these should have them?

I think that job is dealt with by that spring contraption?

[Keyo 47]

Here are all the parts from a late Mk3 golf VR6 288 mm . 

https://www.ilcats.ru/vw/?function=getParts&market=RDW&model=GO&modelcode=184&year=1997&group=6&subgroup=615&part=615040&language=en

[fendervg 32]

On 6/5/2021 at 4:42 PM, Cressa said:

They will come back looking mint.

Can you see if there is an anti rattle plate fitted at the carriers where the pads sit . I always wondered whether these should have them?

I think they don't have the anti rattle plate because the pad on the piston side clips into the piston with three spring plates that are attached to the back of the pad.

[Keyo 47]

So guys before I send the 288 mm off for refurb . 
 

cupra brake upgrade 4 pot. . 
 

what do we now about this mod - size of brakes - fit stock alloys - modding required to fit - maybe to heavy for wheel  sprung weight ? 
 

year of Cupra  r they come off ? 
 

cheers 

Edited June 7, 2021 by Keyo