Jump to content

Engine Bay

Engines, induction, tuning, cooling, sensors and all things under your bonnet!

Subforums

  1. Only Charged Dubs

    A special sub-forum discussion area dedicated for Forum Sponsors "Only Charged Dubs"

    196
    posts

19,689 topics in this forum

  1. Fuel pump buying advice.

    By robrado974,
    • 4 replies
    • 1,094 views

  2. Crackpipe/transfer pipe drain ideas?

    By Cressa,
    • 6 replies
    • 1,211 views

  3. Poor idle , now spluttering .

    By robrado974,
    • 4 replies
    • 1,036 views

  4. Early Corrado AGU Conversion

    By TomBarker1991,
    • 8 replies
    • 3,395 views

  5. 93 Corrado VR6 will not stay running

    By Fc170,
    • 5 replies
    • 1,413 views

  6. plug n play g60 ecu -kdata

    By steveo29,
    • 1 reply
    • 1,644 views

  7. 16 V 9A loss of power / missing when warm

    By Jim H,
    • 16 replies
    • 2,669 views

  8. M25 Breakdown

    By oneohtwo,
    • 11 replies
    • 2,598 views

  9. Auxillary water pump

    By Too Tall,
    • 22 replies
    • 4,969 views

  10. What are these bolts for?

    By BarryNL,
    • 9 replies
    • 1,717 views

  11. VR Engine Bay Residual Heat

    By oneohtwo,
    • 6 replies
    • 1,378 views

  12. VR6 ECU is toast 😥😥😥

    By graham1971,
    • 15 replies
    • 28,844 views

  13. coolant fan running when cold and engine off

    By viking64,
    • 11 replies
    • 2,271 views

  14. VR6 Crank pulley bolt keeps falling out 1 2

    By Serial,
    • 28 replies
    • 8,526 views

  15. Vr6 outside temp sensor

    By Jon_vr6,
    • 3 replies
    • 947 views

  16. Question on VR6 knock sensor

    By fendervg,
    • 5 replies
    • 3,779 views

  17. G60 co pot/ relocation ?

    By Brian1975,
    • 3 replies
    • 1,000 views

  18. G60 motor mount upgrade for TDI motor

    By Lucassayers7,
    • 1 reply
    • 867 views

  19. VR6 Fuel Rail Wanted

    By virtuoso23,
    • 6 replies
    • 1,399 views

  20. Starting Issues & Leaky Fuel Lines

    By DaveVR,
    • 10 replies
    • 1,787 views

  21. VR6 Codes and running rough

    By edition,
    • 18 replies
    • 2,668 views

  22. G60 pistons and torque settings

    By Caddy-g60,
    • 8 replies
    • 1,511 views

  23. Corrado 9A ECU Pin outs needed!

    By 9Arebuild,
    • 3 replies
    • 962 views

  24. Looking for vr6 power steeringpump and starter

    By corradofan,
    • 3 replies
    • 1,112 views

  25. Vr6 cylinder torque procedure-a bit wavy

    By virtuoso23,
    • 16 replies
    • 2,633 views
×
×
  • Create New...